Sealed and Center-Balanced: The Making of CastMan Deep Water
The short version: CastMan Deep Water is built for one job — the long, slow fall over deep structure. A measured 1.2mm epoxy shell over holographic foil, a through-wired body, a center-balanced shape that falls flat instead of nose-first, and BKK twin assists already fitted to a welded solid ring. Two sizes, ten colorways, fishable out of the sleeve. Here is what is inside it, and why each part is there. For the technique itself, read the Slow Pitch Jigging Guide for Deep Water.
Built for One Job
Most metal jigs are asked to do everything — cast, troll, speed jig, bottom bounce. CastMan Deep Water is not. It was drawn for the slow pitch drop over reef, wreck and hard bottom in roughly 75 to 300 feet, and every decision in it serves that one descent. 150g at 5½ inches and 250g at 6½ inches, for amberjack, grouper, snapper and tuna. No weird shapes. Through wired, epoxy vault for supreme durability, solid hardware, and colors for every occasion.
The Shimmer Drop
Give it slack and the jig levels out flat and horizontal, then flutters down in a tight, high-frequency shimmer. That is the Shimmer Drop, and it comes from where the weight sits: the body is center-balanced, not nose or tail loaded, deliberately profiled shaped so it holds its attitude in current instead of rolling over and diving. Stay vertical and stay hooked-up.

Same drop, same beats. A nose-weighted body covers a narrow column; a center-balanced one sweeps across it.
This matters because most deep bites come on the fall, not the lift. A jig that noses over is finished with the strike zone in seconds. One that stays flat keeps working the whole way down, throwing flash sideways the entire time.
The Epoxy Vault
Most jigs get a clear coat. Deep Water gets a measured 1.2mm epoxy shell — about the thickness of a credit card and a half — poured over the holographic foil and cured hard. Teeth, reef structure and hook rash stop at the shell. The foil underneath is sealed in, not painted over, so it keeps its depth and its flash through a season in the jig bag.

Three Ways to See It
Under a UV lamp the shell stops being invisible. The clear material fluoresces on its own, separately from the foil beneath it, and you can read it as what it is — a formed body with its own edges and its own surface, wrapped around the jig. Look at where that surface runs over the eye socket, and at the clear lip standing proud along the bottom edge.

Clown Glow, 250g, under UV. The clear shell lights up independently of the foil — the easiest way to see it as a separate layer rather than a coat of paint.
In daylight it is the eye that gives it away. Each eye is a domed 3D holographic unit set into a molded recess in the head, then poured over with everything else. The shell's surface runs straight across the top of it — the highlight you see is sitting on the epoxy above the eye, not on the eye itself.

Mahi, 250g. The eye sits in a recess below the shell surface. A stick-on eye on a jig that spends its life against reef and hook points is a question of when, not whether.
And the finish is under there with it. The holographic foil and the printed COLMANTS mark are both beneath the clear layer, not on it. Nothing on the outside of this jig can be scuffed off, because nothing is on the outside.

Mahi, 250g. Foil and print, both sealed under the shell.
The number that matters is that it is the same 1.2mm at 250g as at 150g. Thinning the coat on the heavier size is the easy way to save money on a jig like this, and we did not do it.
UV-Reactive Foil on Every Color
Not an accent on select patterns — all ten colorways. Color is the first thing water takes away, and by a couple of hundred feet most of the spectrum is gone. What still reaches down there is blue-violet, and that is the light the foil fluoresces under. On the glow patterns, glow sits on top of that for the deepest water and the low-light bite.
Redbelly Shiner under a UV lamp, and Midnight Glow after charging, in the dark. At depth the trigger is the blue end of what is left of the sunlight rather than a lamp, but the pigment responds the same way.

Approximate, for clear offshore water. Inshore and stained water compresses every band.
Through-Wired, Nose to Tail
Everything above is finish and balance. This part is structure.
A single wire runs the full length of the jig, nose to tail, and closes into the loop your hardware hangs from. The body is formed around it. That means the line tie is not an eye anchored in the casting — the load runs through the wire, end to end, and the body rides on it.
It matters because of how the alternative fails. On a jig with an eye set only into the body, everything is fine until it is not: a big amberjack loads the rod, the eye starts to work in its seat, and it either straightens or pulls out. There is rarely a warning, and it never happens at a convenient moment. Through-wiring does not make that less likely — it removes the failure from the design.
It is also the one part of a jig you cannot check for yourself. You can see the foil. You can measure the epoxy with a caliper. You can read the split ring rating off a packet. The wire is sealed inside a finished lure, which is exactly why it is worth saying out loud rather than assuming everyone builds it this way.
Rigged and Ready
The nose carries a three-part stack, and the assists that hang off it are bound to match. Each piece has a job:
- The nose loop is the front end of the through-wire, closed at the head and sealed under the epoxy.
- The split ring — rated 200 to 300 lb — is where your snap or leader goes.
- The welded solid ring carries the assists, so the cords never ride in the split ring's gap — which is where a cheaper build wears through.
- The assist cords are aramid — high tensile strength with almost no stretch, and resistant to being cut where they ride against the jig and a fish's teeth. Each one is bound to its hook with ultra-high-tensile thread under a marine-grade epoxy seal.
BKK twin assist hooks come fitted and matched to the weight: 4/0 at 150g, 5/0 at 250g. Tie it on and fish it out of the sleeve. If you run a tail assist, or you prefer longer cords, add what you like — you are tuning a rig rather than building one.

Everything in the photo ships in the sleeve. Clown Glow, 250g.
What to Use When
| Conditions | Size | Assists |
|---|---|---|
| Lighter current, roughly 75–200 ft | 150g · 5½ in | 4/0 |
| Deeper water or heavier current, roughly 200–300 ft | 250g · 6½ in | 5/0 |
The rule behind the chart is simple: stay vertical. If your line starts angling out behind the boat, go heavier. A jig being dragged by current never falls the way it was designed to. Full weight and color charts are in the jigging guide.
Where It Was Tested
Deep Water went through a charter season at Race Point, Provincetown — striped bass to 48 inches in 75 to 175 feet of water. The jigs came back with the finish and the terminal hardware intact. That is the kind of use that finds a thin clear coat quickly.
The Line
Ten colorways across both sizes, from the reds and oranges that work shallow, through the chartreuse, greens and blues that carry deeper, to the glows and darks for the bottom of the range. CastMan Deep Water Slow Pitch Jigs are the deep-jigging extension of the CastMan ARMOR line — the same Epoxy Vault process, drawn for a different job. The story behind that finish is in Metal Jigs Evolved.
Orders over $55 ship free, and we ship every day from Fort Walton Beach, Florida.
Tight lines! 🎣
— The COLMANTS Team